Wire Rope Clip - Miami Cordage

Products

Type 304 stainless steel U-bolt wire rope clips are most often used in rigging applications to secure the wire rope on the turn back and are ideal for use with moderate load applications. Please refer to the instructions below for more information on wire rope clips.

  • Type 304 stainless steel and precision cast
  • Import wire rope clips also available

35

Part # A
(in)
B
(in)
C
(in)
D
(in)
E
(in)
Wt
(lb)
WRCS116SUN 1/16 0.09 0.40 0.52 0.55 0.02
WRCS18SUN 1/8 0.12 0.43 0.55 0.62 0.02
WRCS532SUN 5/32 0.15 0.56 0.70 0.73 0.04
WRCS316SUN 3/16 0.19 0.67 0.78 0.87 0.06
WRCS14SUN 1/4 0.23 0.75 0.84 1.11 0.09
WRCS516SUN 5/16 0.31 0.90 1.06 1.34 0.17
WRCS38SUN 3/8 0.38 1.00 1.32 1.74 0.36
WRCS12SUN 1/2 0.47 1.40 1.48 1.97 0.52
WRCS916SUN 9/16 0.47 1.50 1.70 2.05 0.61
WRCS58SUN 5/8 0.54 1.87 1.83 2.33 0.89
WRCS34SUN 3/4 0.54 2.00 2.05 2.42 1.03
WRCS78SUN 7/8 0.61 2.32 2.41 2.81 1.57
WRCS1SUN 1 0.61 2.41 2.40 2.97 1.81
WRCS114SUN 1-1/4 0.85 2.32 3.16 4.12 4.45
Proper Use of Fist Grips, Chair Wire Rope Clips
  1. Turn back specified amount of rope from thimble or loop. Apply first clip one base width from dead end of rope. Tighten nuts evenly, alternating from one nut to the other until reaching the recommended torque.
  2. When two clips are required, apply the second clip as near the loop or thimble as possible. Tighten nuts evenly, alternating until reaching the recommended torque. When more than two clips are required, apply the second clip as near the loop or thimble as possible, turn nuts on second clip firmly, but do not tighten.
  3. When three or more clips are required, space additional clips between first two—take up rope slack—tighten nuts on all clips, alternating from one nut to the other until reaching the recommended torque.
  4. Apply an initial load equal to loads expected in use. Inspect for proper spacing and retighten the nuts to the recommended torque.

fist grip
If a pulley (sheave) is used for rope turn-back, add one additional clip.

The number of clips shown is based upon using RRL or RLL wire rope, 6 x 19 or 6 x 37 Class, FC or IWRC, IPS or XIP. If Seale construction or similar outer wire type construction in the 6 x 19 Class is to be used for sizes 1″ and larger, add one additional clip The number of clips shown also applies to rotational-resistant RRL wire rope, 8 x 19 Class, IP, IIP, sizes 1-1/2″ and smaller, and to rotation-resistant RRL wire rope, 19 x 7 Class, IPS, IIP, sizes 1-1/2″ and smaller. For other classes of wire rope, additional clips may be necessary. Length of rope turn-back should be increased when more clips are used. Efficiency ratings for wire rope end terminations are based upon the breaking strength of wire rope. The efficiency rating of a properly prepared loop or thimble eye termination for clip sizes 1/8″ through 7/8″ is 80% and for sizes 1″ through 1-1/2″ is 90%. In accordance with good rigging and maintenance practices, the wire rope end termnation should be inspected periodically for wear, abuse and genera adequacy.